SPA-1XCHSTM1/OC3

Model

SPA-1XCHSTM1/OC3

Product compatibility

• ● Cisco 7600 Series Routers
• ● Cisco ASR 1000 Series Routers
• ● Cisco ASR 9000 Series Routers

Cards, ports, and slots

1 port

Power

• ● 2-port: 7.7W maximum
• ● 4-port: 8.4W maximum

Physical specifications

Weight: 0.75 lb (0.34 kg)

Height: 0.8 in. (2.03 cm)

Width: 6.75 in. (17.15 cm)

Depth: 7.28 in. (18.49 cm)

Model

SPA-2XCHOC12/DS0

SPA-1XCHSTM1/OC3

Type

Cisco ASR 9000 Series Shared Port Adapter

Cisco Router Shared Port Adapter

Product compatibility

Cisco ASR 9000 Series Router

• ● Cisco 7600 Series Routers
• ● Cisco ASR 1000 Series Routers
• ● Cisco ASR 9000 Series Routers

SPA-1XCHSTM1/OC3 Specifications

Product compatibility

· Cisco 7600 Series Routers

· Cisco ASR 1000 Series Routers

· Cisco ASR 9000 Series Routers

Minimum software version

· Cisco 7600 Series Routers: Cisco IOS® Software Release 15.4(2)S and Cisco IOS XE Software Release 3.12.0.0S

· Cisco ASR 1000 Series Routers with Cisco IOS XE Software Releases 3.12.0,3.11.2, and 3.10.3

· Cisco ASR 9000 Series Routers with Cisco IOS XR Software Release 5.2.0

Protocols

Serial encapsulations:

· High-Level Data Link Control (HDLC)

· Point-to-Point Protocol (PPP), RFC 1662

· Frame Relay, RFC 1490

Multilink support (bundle limit dependent on number of links per bundle; maximum of 12 links per bundle):

· Multilink PPP (MLPPP), RFC 1990

· Link fragmentation and interleaving (LFI) over Frame Relay (FRF.12) and MLPPP

Networking protocols:

· IPv4/IPv6

Cards, ports, and slots

1 port

Connectivity

OC-3/STM-1 Small Form-Factor Pluggable (SFP) optics module (refer to optical parameters in Table 2)

Features and functions

Up to 84 T1 (or 3 T3) or 63 E1 (or 3 E3) ports

Up to 1022 n x DS-0 channels (where n is 1 to 24) with no T3 ports configured

Up to 400 n x DS-0 channels (where n is 1 to 24) with one or more T3 ports configured

Support for Channelized OC-3 to T1, Channelized STM-1 to E1, clear channel T3/E3, subrate T3/E3, full-rate T1, clear channel E1, and Channelized T1/E1

SONET multiplexing:

· OC-3 <-> STS-3 <-> STS-1 <-> VTG <-> VT1.5 <-> T1 <-> N x DS-0

· OC-3 <-> STS-3 <-> STS-1 <-> T3 <-> T1 <-> N x DS-0

· OC-3 <-> STS-3 <-> STS-1 <-> T3

· OC-3 <-> STS-3 <-> STS-1 <-> T3 <-> E1 <-> n x DS-0

SDH multiplexing:

· STM-1 <-> AUG <-> AU-4 <-> VC-4 <-> TUG-3 <-> TUG-2 <-> TU-12 <-> VC-12 <-> E1 <-> n x DS-0

· STM-1 <-> AUG <-> AU-4 <-> VC-4 <-> TUG-3 <-> TU-3 <-> VC-3 <-> T3/E3

· Internal or line-derived (loop) clocking, independently selectable on each T1 or E1 tributary

Loopback capabilities:

· Local and remote loopback at the T3/T1 level

· Network loopback at the STM-1/OC-3, T3/E3, and T1/E1 levels

· Response to embedded loopback commands

· Insertion of loopback commands into transmitted signal

· Bit error rate testing (BERT) pattern generation and detection per channel

· Programmable pseudorandom pattern up to 32 bits in length

· T3/E3: All 0s, all 1s, 215, 220, 220 QRSS, 223, alternating 0s and 1s, 1-in-8, and 3-in-24

· T1/E1: All 0s, all 1s, 211, 215, 220, 220 QRSS, 223, alternating 0s and 1s, 1-in-8, and 3-in-24

· 32-bit error-count and bit-count registers

· Detection of test patterns with bit error rates up to 10-2

· 24-hour history maintained for error statistics and failure counts, at 15-minute intervals

· 16- and 32-bit cyclic redundancy check (CRC); 16-bit default

SONET/SDH-specific features:

· Compliance with G.707, G.783, G.784, G.957, G.958, and GR-253

· Supported SONET/SDH alarm and signal events:

◦   Signal failure bit error rate (SF-BER)

◦   Signal degrade bit error rate (SD-BER)

◦   Signal label payload construction (C2)

◦   Path trace byte (J1)

· Section

◦   Loss of signal (LoS)

◦   Loss of frame (LoF)

◦   Error counts for B1

Line

· Line alarm indication signal (LAIS)

· Line remote defect indication (LRDI)

· Line remote error indication (LREI)

· Error counts for B2

Path

· Path alarm indication signal (PAIS)

· Path remote defect indication (PRDI)

· Path remote error indication (PREI)

· Error counts for B3

· Loss of pointer (LOP)

· New pointer events (NEWPTR)

· Positive stuffing event (PSE)

· Negative stuffing event (NSE)

· Path unequipped indication signal (PUNEQ)

· Path payload mismatch indication signal (PPLM)

T3-specific features:

· Channelized T3 with 28 DS-1 lines or 21 E1 lines multiplexed into a T3

· Unchannelized T3 supporting subrate and scrambling formats for Digital Link, ADC/Kentrox, Larscom, Adtran, and Verilink data service units (DSUs)

· C-bit or M23/M13 framing

· Maintenance data link (MDL)

· T3 far-end alarm and control (FEAC) channel support

· Alarm monitoring

· Alarm indication signal (AIS)

· Out of frame (OOF)

· Far-end receive failure (FERF)

· Performance data collection:

◦   Framing bit errors (FERR) (F- or M-bit errors)

◦   P-bit error counts (path-parity errors)

◦   C-bit error counts

◦   Far-end block error (FEBE) counts

E3-specific features:

· G.751 framing

· Alarm monitoring

· AIS

· OOF

· FERF

· Performance data collection:

◦   Framing pattern errors

◦   BIP-8 error counts (path-parity errors)

◦   FEBE counts

· T1-specific features:

◦   D4 Super Frame (SF) or Extended Super Frame (ESF) framing

◦   ANSI T1.403 and AT&T TR 54016 Facility Data Link (FDL) support

◦   Alarm monitoring

◦   AIS

◦   OOF

◦   Far-end alarm failure (yellow or distant alarm)

Performance data collection:

· CRC/bit errors

· Framing bit errors

· Line errored seconds

· Far-end errored seconds

· Far-end severely errored seconds

· Far-end unavailable seconds

E1-specific features:

· CRC4 or non-CRC4 framing in conformance with ITU-T G.703 and G.704

· Alarm monitoring

· AIS

· OOF

· Remote alarm indication (RAI)

· Performance data collection

· CRC/bit errors

· Framing bit errors

· FEBE

Reliability and availability

OIR

Field-replaceable SFP optics modules

Support for both 1 + 1 SONET Automatic Protection Switching (APS) and SDH Linear Multiplexer Section Protection (MSP) protocols

Single SPA software reset

MIBs

RFC 2558 MIB (SONET/SDH)

RFC 2495 MIB (T1/E1)

RFC 2496 MIB (T3/E3)

Network management

Simple Network Management Protocol (SNMP)

Physical specifications

Weight: 0.75 lb (0.34 kg)

Height: 0.8 in. (2.03 cm)

Width: 6.75 in. (17.15 cm)

Depth: 7.28 in. (18.49 cm)

Regulatory compliance

CE marking

Safety: UL/CSA/IEC/EN 60950-1, IEC/EN 60825 Laser Safety, AS/NZS 60950, FDA Code of Federal Regulations Laser Safety

EMC: FCC Part 15 Class A, ICES 003 Class A, AS/NZS 3548 Class A, CISPR 22 Class B (up to 1GHz), EN55022 Class B (up to 1GHz), VCCI Class A, BSMI Class A, EN 300 386 Telecommunications Network Equipment (EMC), EN50082-1/EN61000-6-1 Generic Immunity Standard, EN55022 Information Technology Equipment (Emissions), EN55024 Information Technology Equipment (Immunity), IEC/EN61000-3-2 Power Line Harmonics, IEC/EN61000-3-3 Voltage Fluctuations and Flicker, IEC/EN61000-4-2 Electrostatic Discharge Immunity (8kV contact, 15kV air), IEC/EN61000-4-3 Radiated Immunity (10V/m), IEC/EN61000-4-4 Electrical Fast Transient Immunity (2kV power, 1kV signal), IEC/EN61000-4-5 Surge AC Port (4kV CM, 2kV DM), IEC/EN61000-4-5 Surge Signal Port (1kV), IEC/EN61000-4-5 Surge DC Port (1kV), IEC/EN61000-4-6 Immunity to Conducted Disturbances (10Vrms), IEC/EN61000-4-8 Power Frequency Magnetic Field Immunity (30A/m), IEC/EN61000-4-11 Voltage Dips, Short Interruptions, and Voltage Variations, GR-1089-CORE NEBS EMC and Safety, GR-63-CORE NEBS Physical Protection, SR-3580 NEBS Criteria Levels (Level 3)

Telecom (OC3): GR-253

Telecom (STM-1): G.783, G.957

Environmental Specifications

Operating temperature: 41 to 104°F (5 to 40°C)

Storage temperature: -38 to 150°F (-40 to 70°C)

Operating humidity: 5 to 85% relative humidity

Storage humidity: 5 to 95% relative humidity